|
Mini-Tower Chassis -- Removing and Replacing Parts: Dell OptiPlex GX100 Systems
Service Manual
Back to Contents Page
Mini Tower Chassis — Removing and Replacing Parts: Dell™
OptiPlex™ GX100 Systems Service Manual
This section provides procedures for removing and replacing the components, assemblies,
and subassemblies in the Dell OptiPlex mini tower chassis GX100 system.
Unless otherwise noted, each procedure assumes that the following conditions exist:
- You have performed the steps in "
Precautionary Measures."
You have removed the computer cover.
You can replace or reinstall a part by performing the removal procedure in reverse order
unless additional information is provided.
Most of the procedures in this file require the use of one or more of the following
tools:
- Small flat-blade screwdriver
- Wide flat-blade screwdriver
- #1 and #2 Phillips-head screwdrivers
- 1/4-inch nut driver
Also, use a wrist grounding strap as explained in "Precautionary Measures."
Before you perform any of the procedures in this file, take a few moments to read the
following caution for your personal safety and to prevent damage to the system from ESD.
 |
CAUTION: FOR YOUR PERSONAL SAFETY AND PROTECTION OF THE
EQUIPMENT Before you start to work on the
system, perform the following steps in the sequence listed:
- Turn off the computer and all peripherals.
- Disconnect the computer and peripherals from their AC power sources.
Also, disconnect any telephone or telecommunication lines from the computer. Doing so
reduces the potential for personal injury or shock.
- If you are disconnecting a peripheral from the computer or are
removing a component from the system board, wait 10 to 20 seconds after disconnecting the
computer from AC power before disconnecting the peripheral or removing the component to
avoid possible damage to the system board.
- Wear a wrist grounding strap, and clip it to an unpainted metal
surface, such as the padlock loop on the back of the chassis. If a wrist grounding strap
is not available, touch any unpainted metal surface on the back of the computer or on the
computer chassis, such as the power supply, to discharge any static charge from your body
before touching anything inside the computer. While you work, periodically touch an
unpainted metal surface on the computer chassis to dissipate any static electricity that
might harm internal components. Also avoid touching components or contacts on a card and
avoid touching pins on a chip.
- Verify that the auxiliary power indicator on the system board is not
on. If it is on, you may need to wait 10 to 30 seconds for it to go out (see Item 13 of Figure 24).
|
Figure 1 shows a side view of the mini
tower chassis computer to help orient you when you work inside the
computer.
Figure 1. Mini Tower
Chassis Orientation View
 |
| 1 |
System board |
| 2 |
Power supply |
| 3 |
5.25-inch drive slots |
| 4 |
Internal hard-disk drive bracket |
| 5 |
Expansion-card cage |
| 6 |
Bottom of computer |
|
Figure 2 shows the mini tower chassis with the
cover removed.
Figure 2. Inside the
Mini Tower Chassis
 |
| 1 |
5.25-inch drive slots |
| 2 |
hard-disk drive bracket |
| 3 |
Chassis intrusion switch |
| 4 |
Hard-disk drive interface cable |
| 5 |
Expansion-card cage |
| 6 |
System board |
| 7 |
Riser board |
| 8 |
Padlock ring |
| 9 |
I/O ports and connectors |
| 10 |
Security cable slot |
| 11 |
AC power receptacle |
| 12 |
Power supply |
|
Figure 3. Computer Cover Removal
To remove the mini tower computer cover, perform the following steps:
- Face the back of the computer and slide the upper half of
the padlock ring to the left to unlock the cover release mechansism (see figure 3).
- Face the left side cover
and press the release button, located at the
bottom-left corner of the front bezel (see Figure 3).
- Lift the bottom of the cover, allowing it to pivot up toward
you.
- Disengage the tabs that secure the cover to the top of the
chassis, and lift the cover away.
To replace the mini
tower computer cover, perform the following steps:
- Face the left side of the computer and hold the cover at a slight angle, as shown in
Figure 4
.
- Align the top of the cover with the top of the chassis and insert the hooks on the cover into the recessed slots on the computer
chassis so that the tabs catch the hooks inside the slots.
- Pivot the cover down toward the bottom of the chassis and into
position.
Make sure that the securing hooks at the bottom of the
cover click into place.
- If you are using a padlock to secure your system, reinstall the
padlock.
Front Bezel
Figure 5. Front Bezel Removal
 |
| 1 |
Tab release |
| 2 |
Retaining hooks (2) |
|
To remove the front bezel, perform the following steps:
- While pressing the tab release marked with
the icon, tilt the bezel away from the chassis.
- Disengage the two retaining hooks at the bottom of the bezel
.
- Carefully pull the bezel away from the chassis.
To replace the front bezel, perform the following
steps:
- Fit the two retaining hooks on the bezel into their corresponding
slots at the bottom of the mini tower chassis.
- Rotate the bezel toward the chassis until the tabs on the top of the
chassis snap into their slots on the bezel.
Figure 6.
Eject, Power, and Reset Button Removal
 |
| 1 |
Diskette eject button |
| 2 |
Power button |
| 3 |
Reset button |
|
To remove the eject, power, and reset buttons, perform the following steps:
- Lay the front bezel on a flat work surface, with the back of the bezel facing up.
To remove the 3.5-inch diskette eject button, pull gently on the plastic part of the
button until it comes free.
To remove the power button or the reset button, use a small screwdriver and push in the
two or three plastic clips that hold the button to the bezel.
When these clips are released, the buttons come free from the bezel.
Figure 7. 5.25-Inch
Front-Panel Insert Removal
 |
| 1 |
Front panel insert |
| 2 |
Bezel |
| 3 |
Ring tab (2) |
|
To remove a 5.25-inch
front-panel insert, perform the following steps:
- Hold the bezel with the front facing you.
- From the front of the bezel, use your thumbs to press inward on the insert until it
snaps free of the bezel.
To replace a 5.25-inch front-panel insert, position the two ring-tabs over the posts on
the inside of the bay opening, and then press the ring tabs over the posts.
Figure 8. Control Panel Removal
 |
| 1 |
Control panel |
| 2 |
Control panel connector |
| 3 |
Chassis intrusion cable
connector |
| 4 |
Chassis intrusion switch |
|
To remove the control panel, perform the following steps:
- Disconnect the control panel cable from the
control
panel connector on the system board (see "System Board Labels" for the location of the PANEL
connector).
Note the routing of the control panel cable as you remove it from the chassis.
Disconnect the the chassis intrusion switch cable connector
from the control panel.
Remove the mounting screw that secures the control panel to
the chassis.
Remove the control panel cable.
Pull the control panel cable through the opening in the
front wall, and carefully remove the cable from the routing tab in the chassis.
Pull out on the control panel to detach it from the chassis.
Note the routing of the control panel cable as you remove it
from the chassis.
Figure 9. Chassis
Intrusion Switch Removal
 |
| 1 |
Control panel |
| 2 |
Control panel cable connector |
| 3 |
Chassis intrusion cable connector |
| 4 |
Chassis intrusion switch |
|
To remove the chassis intrusion switch, perform the following steps:
- Remove the control panel from the front
panel.
- Disconnect the chassis intrusion switch cable from the control
panel (see Figure 9).
Note the routing of the chassis intrusion cable as you remove the
cable from the chassis. Chassis hooks may hold the cable in
place inside the chassis.
- Slide the chassis intrusion switch out of its slot on the chassis and carefully remove
the switch and its attached cable from the chassis.
- Install the replacement chassis intrusion switch and cable.
- To reset the chassis intrusion detector, enter System Setup and reset
Chassis Intrusion to Enabled or Enabled-Silent
(see your User's Guide for instructions).
 |
NOTE: In all of the following procedures, left and
right refer to your left and right as you face the front of the computer. |
Figure 10. Drive Locations
 |
| 1 |
3.5-inch diskette drive |
| 2 |
5.25-inch drive slots (3) |
| 3 |
3.5-inch internal bay for
hard-disk drives (2) |
|
|
|
3.5-Inch Diskette Drive
Figure 11. Removing a
Diskette Drive From a Drive Bay
To remove the 3.5-inch diskette drive from the drive bay,
perform the following steps:
- Disconnect the DC power and diskette interface cable from
the back of the drive.
- Press the release tab on the left side of the diskette
drive, and pull the diskette drive/bracket out of the chassis.
- Remove the drive-mounting screw from the left side of the
drive, and remove the drive from the bracket. to the bottom of the bracket (see
Figure 11).
When you replace the 3.5-inch diskette drive, be sure that the two
hooks on the right side of the bracket engage the mounting holes in the side of the
3.5-inch diskette drive.
Figure 12. Removing a
5.25-Inch Drive From a Drive Bay
To remove a 5.25-inch drive from a drive bay, perform the following
steps.
|
NOTE: For easier access inside the
chassis, you may want to rotate the power supply out of the way temporarily.
|
- Remove the front bezel.
- Disconnect the DC power cable and the interface cable from the back
of the drive.
- Squeeze the metal tabs that extend from each side of the drive bracket toward each
other, and pull the bracket out of the bay (see Figure 12).
- Lay the 5.25-inch drive/bracket assembly upside down and remove the
four screws that secure the drive to the bracket.
To replace the 5.25-inch drive, perform the following steps:
- Turn the drive upside down, and locate the four screw holes around
its perimeter.
- Place the front of the drive toward the front of the bracket; then
install the four screws, but do not tighten them.
- Align the screws with the score marks on the bracket, and tighten the
screws in the order stamped on the bottom of the bracket.
- Check the alignment of the computer cover around the 5.25-inch bezel.
Adjust the drive forward or backward on the bracket to align it.
- To ensure proper installation, align all screw holes and ensure that
the tabs on the front of the bracket are flush with the front of the drive (see
Figure 13).
Figure
13. Attaching the Drive Bracket to the New Drive
 |
| 1 |
5.25-inch drive |
| 2 |
Bracket tabs (2) |
| 3 |
Bracket |
|
- To further ensure proper positioning of the drive in the bracket,
insert and tighten all four screws in the order in which the holes are numbered
(the holes are labeled "1" through "4").
- Slide the drive into the drive bay until the drive snaps securely
into place (see Figure 14).
Make sure that both bracket
tabs snap into place in the drive bay.
Figure
14. Inserting the New Drive Into the Drive Bay
NOTICE: You must match the colored strip on the cable with
pin 1 on the drive's interface connector to avoid possible damage to your system.
- Connect a DC power cable to the power input connector on the back of
the drive (see Figure 15).
Figure 15. 5.25-Inch Drive Cables Attachment
 |
| 1 |
DC power cable |
| 2 |
EIDE interface connector (on drive) |
|
|
|
|
|
|
|
- Connect the appropriate EIDE interface cable to the EIDE interface
connector on the back of the drive (see Figure 15).
If your
system came with an EIDE CD-ROM or tape drive, use the spare connector on the existing
interface cable. Otherwise, use the EIDE interface cable provided in the drive kit.
Hard-Disk Drive Removal
Figure 16. Hard-Disk Drive Bracket Removal
 |
| 1 |
Drive bracket slide rail |
| 2 |
Chassis hinge slots |
| 3 |
Hinge tabs |
| 4 |
Sliding tab |
| 5 |
Drive bracket |
|
To remove a hard-disk drive from the mini tower's internal
hard-disk drive bracket, perform the following steps.
|
CAUTION: To avoid the possibility of electric
shock, turn off the computer and any peripherals, disconnect them from electrical outlets,
and then wait at least 5 seconds before you remove the computer cover. Also, before you
remove a drive, see the other precautions in "Precautionary Measures." |
- If you are replacing a hard-disk drive that contains data
you want to keep, make a backup copy of your files before you continue this procedure.
Remove the computer cover.
Remove the front bezel.
Open the drive bracket from the chassis:
- Disconnect the DC power cable and EIDE cable from the drive.
- Remove the screw securing the
hard-disk drive bracket to the chassis.
- Grasp the bracket, and rotate it outward from the chassis
until the sliding tab clears the slide rail on the chassis (see Figure 16).
- Lift the bracket up slightly to free its hinge tabs from the
chassis hinge slots.
- Remove the bracket from the chassis.
Figure 17. Hard-Disk
Drive Removal From Bracket
 |
| 1 |
Screws (4) |
| 2 |
Sliding tab |
| 3 |
Drive bracket |
| 4 |
1.6-inch drive |
|
- Remove the four screws that hold the drive in the bracket (see
Figure 17).
Retain the screws for use with the replacement hard-disk drive.
- Remove the drive by sliding it out of the bracket.
Hard-Disk Drive Replacement
To install a replacement hard-disk drive, perform the following
steps.
|
CAUTION: To avoid the possibility of electric
shock, turn off the computer and any peripherals, disconnect them from electrical outlets,
and then wait at least 5 seconds before you remove the computer cover. Also, before you
install a drive, see the other precautions in "Precautionary
Measures." |
NOTICE: To avoid possibly damaging the by electrostatic discharge (ESD), ground yourself by touching an unpainted metal surface on
the back of the computer.
NOTICE: When you unpack the drive, do not set it on a hard
surface, which may damage the drive. Instead, set the drive on a surface, such as a foam
pad, that will sufficiently cushion it.
- Prepare the drive for installation.
Check the documentation for the drive to verify that it is
configured for your computer system.
- If not already done, remove the computer
cover.
- If not already done, remove the
drive bracket from the chassis.
- Slide the drive into the chosen bay of the bracket, orienting the
drive so that the connectors on the back of the drive will face the back of the chassis
when you reinstall the bracket (see Figure 18).
- Align the four screw holes of the drive and bracket. Insert and
tighten the screws from the hard-disk drive you removed in
the previous procedure:
- If you are installing a drive in the 1.6-inch bay, use the four screw
holes in the side of the bracket (see Figure 17).
If you are installing a drive in the 1-inch bay, use the four screw
holes in the bottom of the bracket.
- Reinstall the hard-disk drive bracket in the chassis (see Figure 18):
- Insert the bracket's hinge tabs into the chassis hinge slots so that the tabs hook over
the hinge slots.
- Rotate the bracket toward the chassis, and fit the bracket's sliding tab on the chassis
slide rail.
- Slide the bracket into place, and reinstall the screw you removed in step 4 of the previous procedure.
Figure 18. Drive Bracket Insertion Into
Chassis
 |
| 1 |
Chassis slide rail |
| 2 |
Chassis hinge slots |
| 3 |
Hinge tabs |
| 4 |
Sliding tabs |
|
- Connect a power cable to the power input connector on the back of the
drive (see Figure 19).
Check all connectors to be certain that they are properly cabled and firmly seated.
NOTICE: You must match the red-colored stripe on the EIDE
cable with pin 1 on the drive's interface connector to avoid possible damage to your
system.
- Connect the cable connector on the EIDE
cable to the 40-pin interface connector on the back of the hard-disk drive.
Figure 19. Hard-Disk Drive Cables Attachment
 |
| 1 |
Blue interface connector (on EIDE1) |
| 2 |
Interface cable |
| 3 |
Power cable |
| 4 |
Power input connector on drive |
| 5 |
Interface connector on drive |
|
NOTICE: You must match the blue connector on the interface
cable to the EIDE1 connector on the system board to avoid possible damage to your system.
NOTICE: You must match the red-colored stripe on the EIDE
cable with pin 1 on the IDE1 connector to avoid possible damage to your system.
- If it is not already connected, connect the blue
connector of the EIDE cable to the IDE1 connector on the system board.
To locate the IDE1 connector, see "System
Board Components."
- Replace the computer cover. Then reconnect your computer and peripherals to their electrical outlets,
and turn them on.
If the drive you just installed is the primary drive, insert a
bootable diskette (such as the Dell
Diagnostics Diskette) into drive A.
Turn on the computer system.
Enter System Setup and update the
appropriate Primary Drive option, 0 or 1
(see the online System User's Guide for complete information on System Setup).
After you update the System Setup settings, reboot the system.
Partition and logically format your drive before you proceed to the
next step.
See the documentation for your operating system for instructions.
|
NOTE: On systems with
hard-disk drives larger than 2 GB, create a primary partition of 2 GB and divide the
remaining capacity into partitions of 2 GB or less. For example, a system with a 2.5-GB
hard-disk drive would have a primary partition of 2 GB (drive C) and a second partition of
500 MB (drive D). Hard-disk drives must be partitioned this way because MS-DOS®–based operating systems (including
Microsoft® Windows NT®, when using a FAT16 file system) do not support drive partitions
larger than 2 GB. |
- Test the hard-disk drive by running the Dell Diagnostics (see the online System User's Guide for complete information.
- If the drive you just installed is the primary drive, install your
operating system on the hard-disk drive.
For instructions,
refer to the documentation that came with your operating system.
Figure 20. Power Supply Removal
 |
| 1 |
AC power cable |
| 2 |
AC power receptacle |
| 3 |
Power supply cradle |
| 4 |
DC power cables |
| 5 |
Securing tab |
|
|
|
|
|
To remove the system power supply, perform the following steps:
- Disconnect the AC power cable from the back of the power supply.
- Free the system power supply from the securing tab labeled
"RELEASE —>" and rotate it upward until it locks.
- Disconnect the DC power cables from the system board and the
drives.
Note the routing of the DC power cables underneath the tabs in the chassis as you remove
them from the system board and drives. It is important to route these cables properly when
you replace them to prevent them from being pinched or crimped.
- Remove the screw above the AC power receptacle.
- Lift up on the power supply cradle tab to release the power supply
from the cradle and slide the power supply toward the front of the computer approximately
1 inch.
- Lower the power supply down and away from the computer.
To remove the expansion-card cage, perform
the following steps:
- Examine any cables connected to expansion cards through the
back-panel openings and disconnect any cables that will
not reach to where the cage must be placed upon removal from the chassis.
- Locate the securing lever (see Figure 21). Rotate the lever upward until it stops in an upright position.
Figure 21. Expansion-Card Cage
Removal
 |
| 1 |
Securing lever |
| 2 |
Tabs (2) |
| 3 |
Slots (2) |
|
- Slide the expansion-card cage out of the chassis.
- Lift the expansion-card cage up and away from the chassis.
To replace the expansion-card cage, perform the following steps:
- With the securing lever in the upright position, align the
expansion-card cage tabs with the slots in the chassis opening for the expansion-card cage
(see Figure 21). Slide the expansion-card cage into
place.
- Rotate the securing lever downward, until it is flush with
the top side of the chassis. Make sure that the riser board is fully seated in the RISER
connector on the system board (see Figure 22).
- Reconnect any cables
you removed in step 1
of the previous procedure.
The mini tower chassis is available with either a PCI riser board
(see Figure 22) or a PCI/ISA riser board (see Figure 23). The PCI riser board
provides five PCI expansion card slots. The PCI/ISA riser board provides three PCI
expansion slots, two ISA expansion slots, and two shared PCI/ISA expansion slots.
Figure 22. PCI Riser Board
 |
| 1 |
Auxiliary power indicator
(AUX_LED) |
| 2 |
PCI expansion slot 5 (PCI5) |
| 3 |
Wake On LAN (WOL) connector |
| 4 |
PCI expansion slot 1 (PCI1) |
| 5 |
Auxiliary power connector |
|
Figure 23. Mini Tower
Chassis PCI/ISA Riser Board
 |
| 1 |
PCI expansion slot 1 (PCI1) |
| 2 |
PCI expansion slot 2 (PCI2) |
| 3 |
PCI expansion slot 3 (PCI3) |
| 4 |
PCI expansion slot 4 (PCI4;
shared with ISA1) |
| 5 |
ISA expansion slot 1 (ISA1;
shared with PCI4) |
| 6 |
Standby power indicator LED (AUX_LED) |
| 7 |
ISA expansion slot 4 (ISA4) |
| 8 |
ISA expansion slot 3 (ISA3) |
| 9 |
ISA expansion slot 2 (ISA2;
shared with PCI5) |
| 10 |
PCI expansion slot 5 (PCI5;
shared with ISA2) |
| 11 |
Remote Wakeup header (WOL) |
|
To remove a riser board, perform the following steps.
NOTICE: To avoid possibly damaging expansion cards or the
system board by electrostatic discharge (ESD), ground yourself by touching an unpainted
metal surface on the back of the computer.
- Remove the expansion-card
cage.
- Remove the expansion
cards installed in the slots.
- Remove the screws securing the riser board to the
expansion-card cage.
The subsections that follow contain procedures for locating or
removing some of the system board components, which are shown in Figure 24.
Figure 24. System Board Components
 |
| 1 |
NIC connector |
| 2 |
Video connector |
| 3 |
Fan power connector |
| 4 |
Serial port 2 connector |
| 5 |
USB connectors (2) |
| 6 |
Keyboard (upper) and mouse
(lower) connectors |
| 7 |
Parallel port (upper) and serial
port 1 (lower) connectors |
| 8 |
System board jumper |
| 9 |
Riser board connector |
| 10 |
EIDE1 connector |
| 11 |
EIDE2 connector |
| 12 |
Diskette/tape-drive connector |
| 13 |
Auxiliary power indicator |
| 14 |
DIMM connectors (2) |
| 15 |
3.3 VDC power connector |
| 16 |
Control panel connector |
| 17 |
DC power connector |
|
Figure 25 shows the location of the PSWD
jumper on the system board.
Figure 25. System Board PSWD Jumper
Jumper pins are small groups of two or more pins on a circuit board.
Plastic jumpers containing a wire fit down over the pins. The wire connects the pins and
creates a circuit.
NOTICE: Make sure your system is turned off before you
change a jumper setting. Otherwise, damage to your system or unpredictable results may
occur.
To change a jumper setting, pull the jumper
off its pin(s) and carefully fit it down onto the pin(s) indicated.
Dell shipped your computer with a PSWD jumper installed, meaning
that password features for this computer system are enabled. When you remove the jumper,
or when you install the jumper on only one of the two pins, the password features for this
computer system are disabled.
Table 1 lists the labels for connectors and sockets on your system
board and gives a brief description of their functions.
Table 1. System Board Connectors and Sockets
| Connector or Socket |
Description |
| AUX_LED |
Auxiliary power indicator |
| B1 |
Battery socket |
| DIMM_x |
DIMM socket |
| DSKT |
Diskette/tape drive interface connector |
| ENET |
Integrated NIC connector |
| FAN |
Microprocessor fan connector |
| IDEn |
EIDE interface connector |
| KYBD |
Keyboard connector |
| MICROPROCESSOR |
Microprocessor connector |
| MONITOR |
Video connector |
| MOUSE |
Mouse connector |
| PANEL |
Control panel connector |
| PARALLEL |
Parallel port connector; sometimes
referred to as LPT1 |
| POWER_1 |
Main power input connector |
| POWER_2 |
3.3-volt V power input connector |
| RISER |
Riser board connector |
| SERIALn |
Serial port connectors |
| USB |
USB connectors |
The mini tower GX100 chassis can accommodate up to five 32-bit PCI
expansion cards. Figure 26 shows an example of a 32-bit PCI
expansion card.
Figure 26. 32-Bit PCI Expansion Card Example
To remove an expansion card, perform the following steps:
- Remove the computer cover.
- If necessary, disconnect any cables connected to the card.
Remove the screw from the mounting bracket of the card you want to
remove.
Grasp the card by its outside corners, and ease it out of its
connector.
If you are removing the card permanently, install a metal filler
bracket over the empty card-slot opening.
|
NOTE: Installing filler brackets over
empty card-slot openings is necessary to maintain Federal Communications Commission (FCC)
certification of the system. The brackets also keep dust and dirt out of your computer. |
Replace the computer cover, and reconnect your computer and
peripherals to their power sources and turn them on.
|
NOTE: After you remove and replace the
cover, the chassis intrusion detector will cause the following message to be displayed at
the next system start-up:
ALERT! Cover was previously removed. |
To reset the chassis intrusion detector, enter System Setup and reset
Chassis Intrusion to Enabled
or Enabled-Silent. See the online System User's Guide for detailed instructions on the Intrusion
detector.
|
NOTE: If a setup password has been
assigned by someone else, contact your network administrator for information on resetting
the chassis intrusion detector. |
Figure 27. Expansion Card
Installation
 |
| 1 |
Expansion-card cage |
| 2 |
Card-edge connector |
| 3 |
Expansion card |
| 4 |
Riser board |
| 5 |
Expansion-card connector |
|
|
CAUTION: Some network cards
automatically start up the system when they are connected. To guard against electrical
shock, be sure to unplug your computer from its electrical outlet before installing any
expansion cards. |
To install an expansion card, perform the following steps:
- Prepare the expansion card for installation, and remove the computer cover.
See the documentation that came with the expansion card for
information on configuring the card, making internal connections, or otherwise customizing
it for your system.
- Remove the screw and remove the metal
filler bracket that covers the card-slot opening for the expansion slot you intend to use
(see Figure 28).
Save the screw to
use when installing the expansion card later in this procedure.
Figure 28. Filler Bracket
Removal
- Insert the expansion card into the
expansion-card connector.
If the expansion card is full-length, insert the front end of the card into the
corresponding card guide on the inside front of the chassis as you insert the card into
its connector. Insert the card's edge connector firmly into the expansion-card slot.
- When the card is firmly seated in the connector, secure the card's
mounting bracket to the chassis with the screw you removed in step
2.
- Connect any cables that should be attached to the card.
See the documentation provided with the card for information
about the card's cable connections.
- Replace the computer cover, and
reconnect your computer and peripherals to their power sources and turn them on.
|
NOTE: After you remove and replace the
cover, the chassis intrusion detector will cause the following message to be displayed at
the next system start-up:
ALERT! Cover was previously removed. |
- To reset the chassis intrusion detector, enter System Setup and reset
Chassis Intrusion to Enabled
or Enabled-Silent.
See the online System User's Guide for detailed instructions on the intrusion detector.
|
NOTE: If a setup password has been
assigned by someone else, contact your network administrator for information on resetting
the chassis intrusion detector. |
Figure 29.
DIMM Removal
To remove a DIMM, perform the following steps:
- Unlatch and rotate the power supply up until it locks (see Figure 20).
- Push outward on the two DIMM socket ejectors simultaneously until the DIMM is released
from its socket.
- Lift the DIMM away from the socket.
To install a DIMM, press the DIMM fully into the socket while closing the ejectors to
lock the DIMM into the socket (see Figure 30).
Figure 30. DIMM
Installation
 |
| 1 |
Ejectors (2) |
| 2 |
Notches (2) |
|
Figure 31.
Microprocessor/Heat Sink Removal
 |
| 1 |
Securing clip |
| 2 |
Press here to release securing clip |
|
|
CAUTION: The microprocessor SEC cartridge/heat sink
assembly can get extremely hot. Be sure that the assembly has had sufficient time to cool
before you touch it.
|
|
NOTE: Dell recommends that only a technically
knowledgeable person perform this procedure.
|
To replace a microprocessor, perform the following steps:
- Remove the computer cover.
- Locate the microprocessor socket on the system board.
- Remove the fan power cable from its connector on the system board. Then, remove two
screws securing the fan to the heat sink assembly, and remove the fan.
- Remove the metal clip that secures the heat sink to the
microprocessor socket. Then remove the heat sink from the microprocessor chip.
- Press down on the folded part of the clip with a small screwdriver to release the clip
(see Figure 30).
The securing clip hooks over tabs on the sides of the socket.
NOTICE: Be careful not to bend any of the pins
when removing the microprocessor from its socket. Bending the pins can permanently damage
the microprocessor.
|
- Remove the microprocessor chip from the socket.
Your microprocessor socket is a zero insertion force (ZIF)
socket with a lever-type handle that secures the chip in, or releases it from, the socket.
To remove the chip, pull the
microprocessor-socket release lever straight out until the chip is released (see Figure
32). Then remove the chip from the socket. Leave the release lever extended so that the
socket is ready for the new microprocessor.
Figure 32. Microprocessor Removal
 |
| 1 |
Microprocessor chip |
| 2 |
Release lever |
| 3 |
Microprocessor socket |
|
|
CAUTION: Ground yourself by touching an
unpainted metal surface on the back of the computer.
|
| NOTICE: Be careful not to bend any of the pins
when unpacking the microprocessor. Bending the pins can permanently damage the
microprocessor. |
- Unpack the new microprocessor.
If any of the pins on the chip appear to be bent, see
the online User's Guide for instructions on obtaining technical assistance.
- Align the pin-1 corner of the microprocessor chip with the
pin-1 corner of the microprocessor socket (see Figure 33).
The pin-1 corner of the microprocessor is the squared off corner (see
Figure 33).
|
NOTE: Identifying the pin-1 corners is
critical to positioning the chip correctly. |
Figure 33.
Microprocessor Chip Installation
 |
| 1 |
Pin-1 corners of chip and socket aligned |
|
|
CAUTION: Ground
yourself by touching an unpainted metal surface on the back of the computer.
|
NOTICE: Positioning the
microprocessor chip incorrectly in the socket can permanently damage the chip and the
computer when you turn on the system.
|
NOTICE: When placing the microprocessor chip
in the socket, be sure that all of the pins go into the corresponding holes on all sides
of the socket. Be careful not to bend the pins.
|
- Install the microprocessor chip in the socket (see Figure
33).
If the release lever on the microprocessor socket is not all the way
out, move it to that position now.
With the pin-1 corners of the chip and socket aligned, align the pins
on the chip with the holes in the socket. Set the chip lightly in the socket and make sure
all pins are headed into the correct holes. Because your system uses a ZIF microprocessor
socket, there is no need to use force (which could bend the pins if the chip is
misaligned). When the chip is positioned correctly, it should seat itself in the socket
with minimal pressure.
When the chip is fully seated in the socket, pivot the microprocessor-socket release lever
back toward the socket until it snaps into place, securing the chip.
- Unpack the heat sink included in your upgrade kit.
Peel the release liner from the adhesive tape that is attached to the
bottom of the heat sink.
- Place the heat sink on top of the microprocessor chip (see Figure 34).
Figure 34.
Heat Sink Installation
 |
| 1 |
Fan screws (2) |
| 2 |
Fan |
| 3 |
Securing clip |
| 4 |
Heat sink |
| 5 |
Celeron™ microprocessor |
| 6 |
Microprocessor ZIF socket |
|
- Replace the heat sink securing clip.
Orient the clip as shown in Figure 34, and hook the unfolded end of the clip over the tab
on the top edge of the socket. Then press down on the folded end of the clip to snap the
clip over the tab on the bottom edge of the socket.
- Replace the fan assembly and secure it with two thumbscrews.
- Install the microprocessor fan cable connector to the FAN connector
on the system board.
- Replace the computer cover, and then
reconnect your computer and peripherals to their power sources and turn them on.
As the system boots, it detects the presence of the new microprocessor and automatically
changes the system configuration information in System Setup.
- Enter System Setup and confirm that the Microprocessor
category correctly identifies the installed microprocessor.
- Run the Dell Diagnostics to verify that the new microprocessor is
operating correctly.
Figure 35.
System Battery Removal
|
CAUTION: There is a danger of the new battery
exploding if it is incorrectly installed. Replace the battery only with the same or
equivalent type recommended by the manufacturer. Discard used batteries according to the
manufacturer’s instructions. |
To remove the system battery, perform the following steps:
- If possible, enter System Setup and print the System Setup screens.
- Rotate the power supply up until it locks (see Figure 20).
- Remove the system battery by carefully prying it out of its socket
with your fingers or with a blunt, nonconducting object, such as a plastic screwdriver.
When you replace the system battery, orient the new battery with the
"+" facing up. Insert the battery into its socket and snap it into place.
Figure 36. System Board
Removal
To remove the system board, perform the following steps:
- Place the computer on its side on a flat surface.
- Disconnect all cables from their connectors at the back of the
computer.
- Remove the expansion-card cage.
- Unlatch and rotate the power supply until it locks (see Figure 20).
- Disconnect all cables from the system board.
- Remove the screw that secures the system board to the bottom of the
chassis.
- Slide the system board toward the front of the chassis until it
stops.
- Carefully lift the system board out of the chassis (be sure to lift
evenly and not twist the system board).
If you are replacing a system board, remove the DIMMs and the
microprocessor/heat sink assembly, and install them on the replacement board. Also, set
the jumpers on the new system board so that they are identical to those on the old board,
unless a microprocessor upgrade is being installed.
When you reinstall the system board, before you slide the system
board back to lock it in position, push down near each slot to engage the grounding clip
onto its corresponding tab. Push evenly on both sides of the system board as you slide it
into position (do not twist the system board).
Back to Contents Page
|
